Product Rating

Log Store

  • Treated wood for long lasting-storage
  • Delivered flat packed with clear assembly instructions
  • Felt tiled roof
  • Slatted sides for good air flow

This product has an estimated lead time of 7-10 working days.


Please Enter Post Code



0.00 extras
loyalty Earn 269 points or more

The store is pressure treated with preservative and has an open front with slatted sides for maximum airflow through the logs. It is fitted with a weatherproof felt tiled roof as standard and conveniently designed in modular format to allow two units or more side by side or a multi-unit of four stores. Stores are delivered in a flat pack format with clear instructions and easy to construct.

PLEASE NOTE, The Weathershield, shown in the picture is NOT included in the log store price and is supplied as an accessory

Dimensions (single log store)

Width: 124cm
Depth: 82cm
Height (front): 167cm
Height (rear): 183cm

Estimated Lead Time
7-10 working days

Assembly Instructions

Before you start

Make sure you place the wood store on a lavel surface suitable to support the weight. Distortion may occur if the store is not placed on a stable surface.

Take the bag of screws and seperate them into individual sizes. you should have the following

Label Length Diameter Quantity
A 20mm 4mm 16
B 45mm 4mm 66
C 60mm 4mm 2
D 60mm 5mm 4
E 80mm 5mm 2
F 90mm 5mm 8


You should also have the following parts


 Tools you will need

  • Battery type screw driver with clutch and pozi drive tip
  • Tape measure
  • Step ladder
  • A willing assistant (to help you lift the log store)

You should consider adjusting your screwdrivers' slip clutch to prevent overpenetration of screwheads. This can cause the wood to splinter.

Step 1

Lay part B (base) on its long edge with legs pointing away from the proposed wood shed construction. Lay part A (side panels) on the ground either side of part B (base) with their longest edge on the ground and the hinges closing inwards.

Line up the top of the case to the top of the lowest cross member. 

Screw four 90mm screws into either side as shown below.


Step 2

To fit the lintel (part D) straighten the two sides and place the lintel at the top of the structure so that it rests on the top of the highest cross member. Secure with 2 80mm screws.

 Step 3

Life the part constructed assembly onto its feet, ensure it is level and insert the lower Part C (back panel). Secure with 45mm screws as shown. Repeat for the upper section. 

Then fit 2 metal brace plates to the centre and base on the rear panels. Use 4 20mm screws for each brace plate



Step 4

The facia palters are in four pieces (parts E x 2 and G x 2). Parts G are the longer parts and have an angle at one end, these should be fitted first with the angle in line with the roof (facing forwards with 5 45mm screws. 

Fit screws X and Y first on each side then straighten the sides before fitting screw Z. Then fit remaining screws and facia panel E. 

Part E is fitted with 2 45mm screws and 1 60mm screw. 

The 60mm screws should be fitted into the log store support feet.


Step 5

Fit the 2 metal brace plates (part I) to the inside front facia uprights using 4 20mm screws for each plate. These plates join Part E and Part G together. 

Step 6 

A) Line roof panels with rear edge and side of log store. 


B) Place part L x2 Rear Roof trim leaving a 70mm gap in the center. 


C)  Fit left and right T sections (part H) and roof cover strip (part F).


D) Fit 4 60mm screws up through the lintel D into the roof section


Once you're finished...

Construction is now finished. Make sure your log store is positioned on a level area which can support the wood store (and all the stored logs). If the store is placed in an unstable location distortion can occur. 

Your wood store has been coated with a preservative to protect it from the elements. To extend the wood store's life inspect the coating yearly and if necessary apply any common wood preservative.

Do not allow children or animals to play in or near the log store, falling logs are heavy and can cause injury.

Your delivery will be made by our own local hi-ab crane lorry. Once your order has been placed we will contact you within the lead time to advise of a delivery date and time. All routes are planned economically.

Customer Reviews